Epoxy Flake Floors in Hemet

Flake floors combine color, grip and easy care, which is why they are Hemet's top pick.

(951) 669-2681

Get a Free Estimate

Tell us about the floor. Only your name and phone are required.

Form powered by splitforms

Worker broadcasting flakes onto an epoxy flake floor in Hemet, CA

Traction you can choose

Less clear coat over the chips means more texture underfoot. More clear coat means a smoother feel. We show you both and help you choose based on who uses the space.

Colors

Light blends brighten a garage. Darker ones hide more. We bring large samples.

Where it goes

Garages, laundry rooms, patios under covers, workshops and small business floors.

How it is installed

Grind, repair, base coat, chips, scrape, topcoat.

Will it stain?

Not from typical garage spills.

How long will it last?

Many years.

Walker-friendly texture

For homes with walkers or canes, a medium texture gives traction without catching rubber tips.

Flake floors with footing in mind

A flake floor gives a garage a finished look while adding texture underfoot. In Hemet, where many homeowners want a floor that feels secure, we can adjust that texture. More chips and a single clear coat leave a grippier surface; extra clear coats make it smoother. We will show you sample boards so you can feel the difference before deciding.

Questions about flake in Hemet

Is it safe for walkers and canes? We choose a texture that adds grip without catching rubber tips.

Will heat soften it? No. We use a UV-stable topcoat rated for high temperatures.

Can I use it on a covered patio? Yes, with a UV-stable top.

What colors hide dust? Tans, grays and mixed desert tones.

Install timeline

Most garages take one to two days, with foot traffic the next morning and parking a few days later.

Low odor options

If you are sensitive to smells, we can use lower-odor products and keep doors to the house sealed during install.

Choosing the right look

Many Hemet homeowners match the chip blend to their cabinets, trim or the color of the house. Bring a sample or photo to the estimate, and we will lay chip boards beside it in your garage light. Lighter blends keep the space bright, and mid-tones hide dust from windy afternoons better than very dark floors do. Smaller chips give a finer, granite-like look in laundry and craft rooms.

Caring for flake

Sweep or blow out dust, rinse with a hose and mop with a mild cleaner. Skip harsh degreasers on the clear top, which can dull the shine.

Detached shops and hobby rooms on bigger lots

Installer broadcasting flake in a hobby workshop in Hemet, CA

Out toward Winchester Road, in Valle Vista and along the quieter roads on the edges of East Hemet, many homes sit on lots big enough for a separate workshop. These buildings get used hard: woodworking, small engine repair, restoring a classic car, or storing a boat for trips to Diamond Valley Lake. Their slabs often were never finished well in the first place, and a flake system turns them into floors that are easy to sweep and hard to stain.

Shop slabs here are usually poured on a simple base with no vapor barrier, sometimes with a rough broom finish. We grind until the surface is open and even, fill holes from old anchors, and repair cracks. Then a pigmented base coat goes down, chips are broadcast to full coverage, and a clear topcoat seals the whole system. We often build the topcoat a little thicker in shops to stand up to rolling tool carts and dropped parts.

Picking a blend that hides sawdust and oil

Tan, brown and black blends are forgiving in a woodshop, where fine sawdust is always on the floor. Grays with flecks of red or black work well for mechanical work where oil drips are part of life. We bring sample boards and look at them in your shop lighting, which is often very different from a house garage.

Outbuildings without power or water

Some detached shops have limited power. Our grinders and vacuums need adequate electrical service, so we check panels and outlets during the estimate and plan for a generator if needed.

Can a flake floor handle a floor jack? Yes, though we suggest a piece of plywood under jack stands for heavy vehicles.

Do roll-up doors cause problems? Not usually. We finish the coating neatly at the door track and seal the edge.

Pick your colors

Call (951) 669-2681.